Everbuild 201 Admix Mortar extended informationUSESLoad bearing brickworkBlock layingExternal/Internal renderingPointing/repointing brickwork.CHARACTERISTICS / ADVANTAGESOut-performs traditional Vinsol Resin Based plasticisers (see specific data).Contains a special additive which keeps air in the mix longer than most other competitive admixtures.Improves trowelabilityEasier tamping down and alignmentImproves workabilityProvides resistance to freeze/thaw cycling down to 20C in both wet and dry mortar.Chloride ion content <0 1%Reduces bleeding.Replaces lime in mix, hence reduces possibility of lime bloom and efflorescence.Everbuild 201 Admix Mortar characteristics and advantagesConforms to BSEN934- Part 3 (2009).Extra tests were carried out in over and above those required by BS4887, to simulate more effectively actual performance requirements in site conditions. One such comparative test is shown below, which simulates the actual loss of air form a mortar mix due to vibration when transferred to site.Freezing Point-100CUsageUsing at an addition rate of 125 - 250cm3 per 50kg cementVol Air Entrained14 - 20%Loss After 1 Hr StandingNot reduced by more than 3% from vol. air entrainedLoss After Extra 15 Mins MixingNot reduced by more than 5% from vol. air entrainedEverbuild 201 Admix Mortar approvals and standards% Air Content After Mixing for..% Air Content After 1 Hour Simulated Work TestBlank5 Mins: 2.92 l 15 Mins: 2.68 | (0.24 loss)Not Tested I -Vinsol Resin5 Mins: 16.75 I 15 Mins: 17.84 I (1.09 Increase)14.01 | 3 83 DecreaseEverbuild M.A5 Mins: 17.10 I 15 Mins: 19.31 | (2.21 Increase)16.23 | 3.01 DecreaseComp. Prod5 Mins• 16.20 I 15 Mins: 17.13. | (0.93 increase)0.93 | 7.35 DecreaseEverbuild 201 Admix Mortar product informationPackaging5Ltr and 25Ltr Jerry Can 200ltr DrumAppearance / ColourDark brown/red liquid with characteristic odour.Shelf LifeUp to 2 years in unopened containers.Storage ConditionsStore in original unopened containers between 5°C and 40°C.Density0.98-1.02 g/cm3pH-Value11.5 - 13.5Conventional Dry Material Content3.6 - 4.4%Total Chloride on ContentAPPLICATION INSTRUCTIONSMixingIn all cases, add to mix at an addition rate of 150ml to 250ml per 50kg cement, depending on the degree of plasticising/entrainment required. Note: remember to reduce required quantity of water accordingly. One litre of EVERBUILD® 201 Mortar Admix added to a 200ltr drum of gauging water will be sufficient for gauging approx. 4 x 50kg cement for mortar or render mixes. Whilst overdosing should be avoided, this formulation does safeguard against moderate overdosing. (up to double the maximum rate). The following are examples of modified mix designs.1: 0.25:3 cement: lime : sand use 1: 3 cement : sand EVERBUILD® 201 Mortar Admix1:1:6 cement : lime : sand. use 1: 6 cement : sand EVERBUILD® 201 Mortar AdmixBRICKLAYING/POINTING: Use a mix design appropriate to brick strength (1 : 3 to 1: 6). INTERNAL RENDERS:1 : 6 EVERBUILD® 201 Mortar Admix EXTERNAL RENDERS: 1 :3 EVERBUILD® 201 Mortar AdmixLIMITATIONSDo not use in structural concrete.Do not overdose.Do not mix with other additives in same gauging water.Do not use in lime based mixes. Categories: All Products, Building Supplies Pallet Deals, Preparation
