Mapei Ultraplan Eco 3210 further informationCoverage: 1.6 Kg/m2 per mm of thickness.Mapei Ultraplan Eco 3210 is a grey powder consisting of special cements with rapid setting and hydration together with graded silica sand, resins and special additives, according to a formula developed in the MAPEI Research and Development Laboratories.Mixed with water Ultraplan Eco 3210 becomes a highly fluid and easily workable mortar, which is self-levelling, with high adhesion to the substrate and dries ultra-quickly.It can be applied with an automatic pressure pump for distances over 100m.It can be spread in thicknesses up to 10 mm per coat without shrinkage, cracking or crazing, and develops very high compressive and flexural strength, as well as resistance to indentation and abrasion.It is ready to receive flooring after approximately 12 hours, regardless of the thickness.It is recommended to wait 24 hours before installing wooden flooring.Recommendations:Do not add water to a mix which has already started to setDo not add lime, cement or gypsum to the mixDo not use Ultraplan Eco 3210 for exterior levelling workDo not use Ultraplan Eco 3210 on substrates subject to continuous rising dampIf a further coat of Ultraplan Eco 3210 needs to be applied once the preceding one is completely dry, first apply Eco Prim TDo not apply Ultraplan Eco 3210 at temperatures below 5°CMapei Ultraplan Eco 3210 Technical DataConsistency:Fine powderColour:GreySpecific gravity (kg/m3):1300Dry solid content (%):100Application DataMixing ratio:4.8 to 5 litres of water per 20 kg bagThickness per coat:3 to 10mmSelf-levelling:YesSpecific gravity of mix (Kg/m3)2000pH of the mix:approx. 12Application temperature range:from 5oC to 30oCOpen time:20-30 minutesSetting time:45-60 minutesSet to light foot traffic:3 hoursTime before laying flooring:12 hours (24 hours for wood flooring)Final Performance DataCompressive strength (N/mm2): 1) – after 1 day 2) – after 3 days 3) – after 7 days 4) – after 28 days: 1) 12.0 2) 17.0 3) 20.0 4) 26.0Flexural strength (N/mm2): a) – after 1 day: b) – after 3 days: c) – after 7 days: d) – after 28 days:a) 3.0 b) 4.0 c) 5.0 d) 7.0Resistance to abrasion Taber Abrasimer (Abrading wheel H22 - 500 g - 200 revolutions) expressed as weight loss (g): i) - after 7 days ii) - after 28 days i) 2.8 ii) 2.3Brinell hardness: 1) – after 1 day: 2) – after 3 days: 3) – after 7 days: 4) – after 28 days: 55 70 80 100APPLICATION PROCEDURE Preparing the substrate Substrates must be completely dry, solid, free from dust, loose areas, paint, wax, oil, rust and traces of gypsum.Cement based surfaces not sufficiently solid must be removed or, where possible, reinforced with Prosfas or Mapeproof ESM.Fissures in concrete substrates must be repaired with Eporip.Cementitious subfloors must be treated with a coat of Mapei Eco Prim T diluted with water 1:2.Anhydrite screeds can be levelled with Ultraplan Eco 3210, but must first be abraded to remove any surface laitance and then primed with a coat of Eco Prim T (diluted with water 1:2), before the application of Ultraplan Eco 3210.Ceramic and natural stone substrates must be cleaned with detergents and abraded and then primed with Eco Prim Grip.Preparing the mix Pour a 20 kg bag of Mapei nUltraplan Eco 3210 into a bucket containing 4.8 to 5 litres of clean water and mix with a low speed electric mixer to obtain an homogeneous lump free mix.Larger quantities can be prepared in on-site mixers.After 2-3 minutes of slackening, restir the mix. The mix is then ready for use.The quantity of Ultraplan Eco 3210 mixed at any time must be used within 20-30 minutes (at 23°C).Spreading the mix Apply Ultraplan Eco 3210 in a single coat from 3 to 10 mm with a large metal trowel or rake keeping the trowel slightly inclined to obtain the desired thickness.Mapei Ultraplan Eco 3210 can also be applied with an automatic pressure pump.Due to its exceptional self levelling properties Ultraplan Eco 3210 immediately loses small imperfections (trowel marks, etc.).When a second coat of Ultraplan Eco 3210 is required, it is recommended to apply it as soon as the first one is set to light foot traffic (approximately 3 hours at 23°C).Ultraplan Eco 3210 is suitable to receive resilient, carpet, and ceramic floor coverings fixed after 12 hours at 23°C (the time can vary, depending on the room temperature and humidity). When installing wood flooring or natural stone, wait 24 hours.Check the humidity content with a carbide hygrometer or an electric moisture meter, keeping in mind that the latter only gives indicative values.Mapei Ultraplan Eco 3210 CleaningWhile still wet, Ultraplan Eco 3210 can be removed from tools with water. View other products by Mapei here. Categories: Floor Levelling & Smoothing Compounds Pallet Deals, Floor Levelling Compounds - Pallet Deals, Smoothing Compounds - Pallet Deals
