ATLAS ULTRA GEOFLEX C2TE S1 25Kg

ATLAS ULTRA GEOFLEX C2TE S1 Gel Adhesive extended informationConsumption:Tiles size [cm]Place of applicationRecommended notches size (mm)Consumption (kg/m3)2 x 2wall floor4 41.3 1.310 x 10wall floor4 61.3 2.015 x 60wall floor6 82.0 2.520 x 25wall floor6 82.0 2.525 x 40wall floor6 82.0 2.530 x 30wall floor6 82.0 2.530 x 60wall floor8 102.5 3.040 x 40wall floor8 102.5 3.050 x 50wall floor8 102.5 3.060 x 60wall floor10 123.0 3.5above 60x60 e.g. 90 x 90, 120 x 20, 300 x 100wall floor10 12 (semi-circular notched trowel)3.0 4.6tiles – slab type* e.g. 20 x 90 or 15 x 100wall floor8 102.5 3.0GEL TECHNOLOGYThe unique gel technology used in ATLAS GEOFLEX WHITE brings the following advantages:adhesive is suitable for any type or size of cladding: especially for extra-large tiles, natural stone,, ceramic, porcelain,consistency of adhesive can be adjusted to individual preferences of the tiler and needs of specific job – mixing ratio is much wider than in case of traditional adhesives,bed depth up to 15 mm – substrate levelling and tiling at once,full spread under the tile with higher mixing ratio – ensured adhesion and durable bond, which is relevant for exterior use,safe cladding installation on surfaces exposed to direct sunlight – during fixing cladding, as well as during mortar setting (e.g. on balcony, terrace).ATLAS ULTRA GEOFLEX PropertiesATLAS ULTRA GEOFLEX is a grey C2TE S1 adhesive for tiles manufactured as a dry mix of high quality cement binder, aggregates and selected modifying agents.S1 deformability – for deformable substrates and extra-large tiles.Wide range of bed thickness from 2 up to 15 mm.No slip from the wall, even for extra-large tiles and stone slabs – cladding can be installed from the top of the wall with no additional support.Perfect support for extra-large tiles (above 5 m2) applied on a floor – heavy tiles do not sunk into adhesive.Walking on and grouting just after 12 hours – owing to accelerated process of adhesive setting and drying.Recommended for tiling in drinking water tanks, food industry, health care facili- ties, nursery houses, kindergartens etc.UseCladding Typeglazed tiles terracotta porcelain tiles laminated tiles natural stone (granite, marble, travertine, syenite, slate)application test required*clinker stoneware ceramic mosaic glass mosaicapplication test required*glass, coloured, printed tilesapplication test required* check recommendations of tiles manufacturerconcrete/cement tiles composite slabs insulation and sound absorbing panels Size of Installed Elementsany tile size, even above 5 m2 slim type tiles Object Typeresidential buildings public access, educational, office and healthcare facilities commercial and service buildings sacral buildings industrial buildings and multi-storey garages industrial warehouses infrastructure buildings SPA objects Installation Areasurfaces with low traffic surfaces with moderate traffic surfaces with large traffic kitchen, bathroom, laundry, garage (in residential buildings) terraces balcony, loggia external slab stairs external post stairs (e.g. cantilever stairs) communication routes facades (including external thermal insulation systems) cladding on a plinths technological reservoirs, swimming pools, fountains, jacuzzi, balneotechnology (without aggresive chemical agents) drinking water reservoirs sauna showers, car washes, rooms washed with plenty of water Substrate Type – Standardcement floors and screeds anhydrite screeds cement, cement-lime plasters gypsum plasters cellular concrete silicate brick or hollow blocks ceramic brick or hollow blocks gypsum blocks Substrate Type – Difficultconcrete terrazzo mineral, dispersive and reactive sealing coats plasterboard drywall screeds (cement or anhydrite) with water or electrical underfloor heating screeds with heating mat embedded in the adhesive plasters with wall heating plasterboards gypsum fibre boards cement fibre boards existing ceramic or stone cladding (tile on tile) resin varnishes on concrete, bonded with substrate dispersive, oil painting coats, bonded with substrate 25 mm) 25 mm) 18 mm) metal and steel plastics ATLAS ULTRA GEOFLEX technical dataBulk density1.25 g/cm3Mixing ratio (water/dry mix)0.27 ÷ 0.36 l / 1 kg 1.35 ÷ 1.8 l / 5 kg 6.08 ÷ 8.10 l / 22,5 kg 6.75 ÷ 9.00 l / 25 kgMin./max. bed depth2 mm / 15 mmdhesive preparation temperature, substrate and ambient temperature during workfrom 5°C to 35°CMaturing time5 minutesPot life*approx. 4 hoursOpen time*min. 30 minutesAdjustability time*20 minutesWalk on/grouting with cement grout*after 12 hoursGrouting with epoxy grout*after 48 hoursFull operation load – foot traffic*after 3 daysFull operation load – vehicle traffic*after 14 daysFull water load – pools/tanks*after 14 daysFloor heating (warm surface)*after 14 daysThe time shown in the table is recommended for the application in the tempera- ture 20°C and humidity 55% (approx.).ATLAS ULTRA GEOFLEX applicationThe substrate should be:stable – sufficiently sound, resistant to deformation, free from materials which would impair adhesion, stabilized.even – maximum adhesive thickness is 15 mm, in case of larger irregularities use, e.g. ATLAS ZW 330 mortar, screeds ATLAS SMS, SAM, POSTAR.clean – free from layers which can impair adhesion, especially dust, dirt, lime, oils, greases, wax, residues of oil and emulsion paints. The substrate coated with algae, fungi, etc. must be cleaned and protected with ATLAS MYKOS no 1 or ATLAS MYKOS PLUS agent. primed with: – ATLAS UNI-GRUNT, ATLAS UNI-GRUNT ULTRA or ATLAS UNI-GRUNT PLUS – substrates of excessive or heterogenous absorptiveness,– ATLAS GRUNTO-PLAST – if the substrate absorptivity is low, or it is coated with layers limiting the adhesion.– ATLAS ULTRAGRUNT – for critical substrates.damp-proofed – in case of tiling on surfaces exposed to water action:– ATLAS WODER E – installation of cladding after 2 hours for damp-proofing and after 4 hours for waterproofing,– ATLAS WODER W, ATLAS WODER S – installation of cladding after 24 h,– ATLAS WODER DUO – installation of cladding after 12 h,– ATLAS WODER DUO EXPRESS – installation of cladding after 3 h.ATLAS ULTRA GEOFLEX Adhesive preparationPour the adhesive from the bag into a container with the suitable amount of water (see Technical Data for ratio) and mix, using a low speed mixer with a drill for mortars, until homogenous. The dispersed adhesive should be left to rest for 5 minutes and then remixed. So prepared adhesive should be used up within approx. 4 hours.Adhesive applicationThe adhesive should be applied onto the surface with a steel trowel and then distributed evenly and shaped (possibly in one direction) with a notched trowel. It is advisable to rub a thin adhesive coat first and then apply the thicker coat and shape it with a notched trowel. It is recommended to lead a notched trowel in one direction. On walls, it’s recommended to shape the adhesive in vertical direction.Placing the tilesAfter the application, the adhesive retains its properties for approx. 30 minutes (in temperature approx. 23 °C and 55 % humidity). Within this time, the tile must be placed and pressed well (the contact surface between the adhesive and the tile should be uniform and as large as possible – min. 2/3 of tile surface). Remove the excess of the adhesive pressed into the joints immediately.In case of floor tiles, tiling outdoors and large size tiles fixing, it is advisable to keep the full bonding surface (use the mixed method consisting in application of the adhesive on the substrate and tile bottom side, if needed). Keep the joint width appropriate for the tile size and operation conditions (check data in the sheets of ATLAS grouts).Tile adjustmentThe position of a tile can be adjusted with delicate moves along the bonding plane. It can be done within approximately 20 minutes since the tile is pressed (in temperature approx. 23 °C and 55 % humidity).Grouting and cladding useFoot traffic and grouting can start after: – approx. 12 hours since the tiles fixing for ATLAS CERAMIC GROUT, ATLAS TIGHT GROUT, ATLAS DECORATIVE GROUT, – approx. 48 hours since the tiles fixing for ATLAS EPOXY GROUT. The mortar reaches the operational strength after 3 days (check the Technical Data). Expansion joints, joints along the wall corners, at sanitary equipment, etc. should be filled with sanitary silicone ATLAS ELASTIC SANITARY SILICONE or ATLAS SANITARY SILICONE SILTON S.Exemplary Steps for installation of claddingStep (following layer)ProductConditioning of the layer before execution of the next step*Substrate levellinglevelling mortar ATLAS ZW 330approx. 5 hscreed ATLAS POSTAR 80 screed ATLAS SMS 15 screed ATLAS SMS 30approx. 1 dayscreed ATLAS POSTAR 20approx. 2 daysscreed ATLAS POSTAR 10 screed ATLAS SAM 100approx. 14 daysscreed ATLAS POSTAR 100 screed ATLAS POSTAR 40 screed ATLAS SAM 200 screed ATLAS SAM 500approx. 21 daysDamp-proofing**ATLAS WODER E ATLAS WODER S ATLAS WODER W ATLAS WODER DUO ATLAS WODER DUO EXPRESSapprox. 2 h approx. 24 h approx. 24 h approx. 12 h approx. 3 hInstallation of tilesATLAS ULTRA GEOFLEXapprox. 12 h – wallGrouting of tilesgrouting mortar ATLAS-ATLAS ULTRA GEOFLEX detailed recommendationsView other products by ATLAS here. Categories: All Products, C2TE - Tile Adhesives Pallet Deals, S1 Tile Adhesives - Pallet Deals